Fuzzy Computerized Automatic
Washing Machine
User's manual
This manual is for
XQS60-78H
Please read this manual
carefully before using.
Retain it for future reference.
W
0030804888A
Names of the parts
Top lid component
Inner cover component
Detergent box
Top lid handle
Round cover
liquid whitener inlet
Control panel
Attachment block
(2 pieces)
Outer tub cover
Balance ring
Pulsator
Water inlet valve
Lint Filter
Water absorption
cushion
Inner tub
Front control board
Cabinet
Handle
Power cord
Drain hose
Base frame
Adjustable leg
Fixed leg (3 pieces)
Back cover
Adjustable leg film
Meaning and description of the symbols
Warning sign Contents marked with that symbol are related to the safety
of the product and the personal safety of the users. Please
operate in strict conformity to the contents, otherwise it may
cause damage of the machine or injure the personal safety
of the user.
Forbidden sign
Contents marked with that symbol are actions forbidden to
perform. Performing of those actions may result in damage
of the machine or injure the personal safety of the user.
Safety precautions
In normal usage of the washing machine, the power
Please plug the plug on special 220V AC receptacle.
Be sure to use single-phase three pins receptacle.
Ensure the earthing prong of the power receptacle is
earthed reliably. Use leakage protector if possible.
plug shall be ready to be pulled or plugged with hang.
Be sure to pull the plug off and close the water faucet
when occurring power failure, delivering the maching,
setting the machine idle or cleaning the machine, do
not plug or pull the power plug with wet hand.
Do not bend, stretch, twist, bind the power cord by force, or reform it.
Do not pressor clamp it with heavy items. If the power cord and power
plug are bad, or the receptacle is loose, be sure to have it replaced by
the technicians of our special shop or our agent, or the after-salesservice
department to avoidany risk. Keep the prong of the power plug clean. If
dust is found on the power plug, please wipe it off with dry cloth.
In case the washing machine is installed on ground
with carpet, be careful not to block the ventilation hole
with carpet.
Do not use water with temperature higher than 50
The ventilation
holes at the bottom
Soft items
Do not wash water-proof laundry like the raincoat,
bike-covers, down textiles etc. To avoid abnormal
vibrations in spinning and damages to the laundries-
Do not put the machine at damp place like the
bathroom. Never wash it with water. Do not
put wet laundries on the front control panel board..
Do not let the machine share one receptacle with other
electric appliances. If the power plug is damaged, or
the plugging into the receptacle is loose, do not use
the plug any more.
Safety precautions
Do not put hand into the rotating tub. It is dangerous
even if the rotation speed is slow. Take special care of
the children. Keep children away from the washing
machine to avoid them climbing on.
Do not decompose, repair or alter the machine by
yourself.
Do not put any hot or heavy items (such as the
kettle with hot water) on the washing machine.
Do not wash laundry with volatile materials
(such as thinner, petrol etc.).
Benzene
Keep the machine away from direct sunlight and
heat source like the heater.
The handicapped or children without care shall not
use the machine.
Please keep the lint filter in good condition, and
install it to proper position during washing. If the
To protect your laundries and washing machine,
please take out all of the coins, buttons, sand, hairpin
lint filter is lost or damaged, please contact the local and other foreign materials before washing.
after-sales service department of our company.
The front cover of lint filter
The back cover of lint filter
dismantle
Please check if the water faucet is open, and if the
connection of the water inlet pipe is proper.
It is suggested to use foamless washing powder.
install
Installation and adjustment
Please install and adjust the machine according to the requirement of the manual.
It is very important to your security and correct operating the machine.
Install the inner cover component
1.Open the top lid of the washing machine.
2.Put the inner cover component on the outer tub cover, aiming the inner cover
shaft to the installation hole of the corresponding outer tub cover shaft groove.
3.Firstly insert the inner cover shaft of one side into the corresponding outer tub
cover shaft groove, then push the another inner cover shaft into the corresponding outer
tub cover shaft groove. Please install to designated position to guarantee there are no
dropping or abnormal sound in opening and closing of the inner cover, and the operation
shall be smooth. Do not dismount the inner cover component after washing.
Outer tub cover
Right hand
Outer tub cover shaft groove
Left hand
Inner cover shaft
Inner cover component
Figure 2
Figure 1
Install the bottom plate
After opening the package, please lean the washing machine gently down on soft items (like
towel cloth, blanket, etc.). Install the bottom plate to the bottom of the machine with eight screws
by a cross screw driver, then lift the machine up gently. See to the figure:
Front
Back
Bottom plate
Soft items
Screw
Adjust the Installation position
The largest allowable slope of the shank base of the machine is 1 . The slanting or rough ground will result in
unstable running or stoppage of the machine. Please adjust it with following methods:
Confirm it's horizontal:
Hang the lead line to check if it is
horizontal.
Adjust the adjustable leg:
1 .To twist the adjustable leg, please first lift up the
side of the leg slightly, loosen the adjustable nut,
and twist the leg.
The adjustable nut
2 . Afteradjustment, fasten the nut.
Loosen
High
Fasten
The adjustable feet
Low
Usage the drain hose
The drainage shall be smooth with the drain hose.
The height of the drain hose shall be less than
10cm, or the drainage will not be smooth, and cost
such long time that the machine may stop at mid
way.
If extra drain hose is needed, please make separate
purchase. The inner diameter of the extra hose shall
not less than 30mm, and the length shall not exceed
1.5m.
>
30mm
Do not step on or press the drain hose.
<1.5m
<10cm
If the drain hose is too long, cut it at mid point. To make
smooth drainage, cut the front end of the hose slantingly.
If the extra hose is too long, cut
it either at A or at B point.
B
A
Install the water inlet hose
Confirm the water faucet
water faucet, suitable
water faucet, not suitable
The exit end face of the faucet
It is required that the front end shall be longer than 10mm.
The exit end face of the faucet shall be flat and smooth. If not please file it to avoid leakage.
Connection between the water inlet hose jointer
and the water faucet
1.Press the lower end of the lock lever and push down the slider. Take off the water inlet hose jointer from the
water inlet hose component. See to Figure 1.
2 Loosen the screw till the water faucet can be accessed. Put the jointer of the water inlet hose on the faucet.
See to Figure 2. (If the faucet is too large and the jointer can not be set on the water faucet, please loosen
the four screws and take out the bushing in the jointer. The front end of the faucet must be smooth,
otherwise it may leak water. See to Figure 3.)
water inlet hose jointer
Screw
Slider
Sign plate
Bushing
Lock level
Screw knife
water inlet hose
Figure 2
Figure 3
Figure 1
3.Fasten the four screws evenly. See to Figure 4.
4 Take off the nameplate. Twist the fastening nut as per the indication of the figure
to seal up the exit end face of the faucet. See to Figure 5.
remark: Before installation, the threading is 4mmabove the upper surface of the nut.
After installation, the threading is 2mm above the upper surface of the nut..(see to figure 6)
About 4mm before twisting
About less than 2mm after twisting
Screw nut
Figure 6
Figure 5
Figure 4
Connection between the water inlet hose and the washer
1.Do not take off the water absorption cushion. Please check if the
cushion is dropped or damaged before each usage. If it happens
please contact our after-sale department immediately.
nut of the water
inlet hose
2 Put the nut of the water inlet hose on the valve jointer.
3 Fasten the nut. Swing it gently to confirm if it's suitable.
water absorption
cushion.
jointer of the
water inlet valve
Connection between the jointer of the water inlet hose
and the water inlet hose
1.Push down the slider. Insert the water inlet hose into the jointer.
the jointer of the
water inlet hose
Slider
2 Hang the lock lever to the jointer. Release the slider till a click
Locking level
sound is heard.
Check the connection between the jointer of the water inlet
hose and the water faucet
1.Swing the hose gently to confirm if it is fastened stable.
2.After installation, open the faucet to check if it leaks.
3.Do not bend the hose with overstrain.
4.Before each usage please check if the connection
between the jointer of the water inlet hose and the
water faucet, and the installation of the water inlet
hose are firm, so as to prevent dropping from
improper installation position.
Dismantle the water inlet hose
1. Close the water faucet.
2. Press the locking lever. Push down the slider. Then pull of the water inlet
hose.
Locking level
Slider
If the machine is used frequently, the jointer of the water inlet hose can be
kept on the faucet to prevent damaging the fixing screw.
1 Preparation before washing
Preparation before washing
1.Connect the water inlet hose.
2.Confirm that the washing machine is earthed
reliably . Then insert the power plug into the
receptacle. Do not connect the earth terminal
to the gas pipe and tap water pipe.
3.Put down the drain hose.
Pay attention to followings before washing the laundries
Confirm if there's
special requirement Take out the coins , and zippers.
for the laundries. sand,hairpins etc.
Clear the pocket.
Fasten the buttons The quantity of the When the pulsator is
laundries shall not running ,the buttons of
exceed the rated the laundries may cause
value. The big noise. For the sake of
laundries like the discretion ,please put
jeans shall be put
in loosely.
the laundries with
buttons into other
laundries.
a. Check if the laundries are applicable for washing with machine.
b. Divide the laundries with infest color from other laundries.
c. Put those laundries difficult to absorb water into water with hand.
d. For those laundries with heavy soil, please first remove the dirt like mud or dust. For the parts with heavy soil,
please apply detergent in advance, which can make it easier to remove the soil.
e. For those laundries that may get lint ball and those with long fur, turn it over before putting in.
f. Do not put those laundries polluted by chemicals directly into the washing machine.
2 Put in the laundries
The capacity of washing of the machine refer to
the largest weight of the standard laundries under
dry condition that can be washed in one time.
Laundries quantity in one washing cycle shall
be lower than the rated capacity. The largest
capacity of this machine is 6.0 kg.
The thickness ,size , type of the cloth will influence
the actual washing capacity. It is suitable to put in
reasonable amount of laundries and the laundries
can be turned round in washing for one time
washing.
Do not select the higher than "4" water level for
laundries less than 1.0kg ,so as to avoid splashing
of water.
3 Put in the detergent
Access for detergent and washing powder
Put the washing powder and softener into the detergent box
directly as Indicated in the left figure.
After that, please close the detergent box. Refer to the following
list for the usage of the detergent :the standard dosage of the
detergent and the water quantity.
Access for softener
How to use softener
See to the manual of softener for the usage
and dosage. When adding softener into the
softener inlet of washing powder box, note
that it shall not exceed the lower side of the cap.
Do not leave the softener for long period after
adding it into the box. Otherwise it may be
solidified and block the inlet.
Detergent box
How to use the whitener
Fill water to decided level .Dilute the whitener with
container. Pour it slowly into the washing tub.
Avoid using whitener on laundries with colour or
pattern as they are prone to lose colour.
As the softener is easy to solidify, please clean
the box frequently. (You shall clean it each time
you use reserve function).
Before use softener, you must select to sterilize
function.
The whitener shall not touch the laundries directly.
Refer to the user's manual for the usage and
quantity of the whitener.
For powder whitener, please dissolve it before use.
How to use the washing powder
Directly dissolved in the machine (not applicable for fuzzy program and reserve wash)
1.Fill small quantity of water.
2.Add the powder Run for 30 seconds to dissolve it completely.
3.Put in the laundry. Select suitable water level.
The instant dissolving of the washing powder:
1.Prepare warm water of 30 and a container.
2.Add the powder while stirring to fully dissolve it In selecting
The super quick program, it is suggested to adopt liquid detergent instead of washing powder to guarantee the washing effect.
The powder is more prone to pollute the laundry than the detergent. Therefore please use it with suitable quantity.
It is suggested not to use high sudsing detergent.
Washing powder with poor quality or long time storage maybe caked. Please pay attention to cleaning the detergent box in time.
4 Use the operation buttons
Description of the function of buttons
Digital tube
Mode and meaning of the indicators
During sensing, it displays
During operation of programs, it displays the remained time
(minute) or remained times of the corresponding procedure
Flashing: indicate the running program
On: indicate the program about to run, or indicate the
selected mode
SOAK
WASH
RINSE
SPIN
RINSE button
SPIN button
WASH button
SOAK button
Push the RINSE button to set the rinse
and disinfect procedure.
Push the SPIN button to set
the spin procedure.
Push the WASH button to set
the wash procedure.
Push the SOAK button to set
the soak procedure.
During STANDARD and JEAN
programs, push the RINSE button to set
different rinse times ( 0, 1, 2, 3, 4times).
During STANDARD and
JEAN programs, push the
SPIN button to set different
spin time (from 0 to 9 minutes)
During STANDARD and
JEAN programs, push the
wash button to set different
wash time (from 0 to 25 minutes)
During STANDARD and
JEAN programs, push the
SOAK button to set different
soak time (10,20,30,40 minutes)
During FIBER and
During FIBER
,
COTTON
,
WOOLLEN and SILK programs, push
the RINSE button to select rinse
procedure, but the rinse times cannot
change.
During FIBER
,
COTTON
,
During FIBER
,
COTTON
WOOLLEN and SILK
WOOLLEN , and SILK
programs, push the WASH
button to select wash
procedure, but the wash time
cannot change.
COTTON programs, push
the soak button to select soak
procedure, but the soak time
cannot change.
programs, push the SPIN
button to select spin procedure,
but the spin time cannot change.
During QUICK
,
POSTHASTE
programs, push the RINSE button, the
machine have no reaction.
During QUICK
,
During QUICK
POSTHASTE , programs,
push the SPIN button, the
machine have no reaction.
During QUICK
,
POSTHASTE
,
WOOLLEN
,
During STANDARD program, the machine
is set to save water program. If you push
the rinse button before starting operation, it
will change to water storage rinse program.
,
POSTHASTE , programs,
and SILK programs, push the
SOAK button, the machine
have no reaction.
push the wash button the
machine have no reaction.
POWER ON/OFF button
CHILD LOCK FUNCTION
Push and hold the WATER LEVEL button and SPIN button, then push down the POWER ON/OFF
button. The digitron displays CL . You can continue setting desired washing procedures.
After setting, push down the START/PAUSE button. The child lock function is activated. All of
the buttons are locked and cannot make selection.
Push the ON/OFF button to switch
on the power.
When the power is on, push it
again to switch off the power.
Push the ON/OFF button to switch
on the power.
Release the child lock function: push down the WATER LEVEL and SPIN button at the same
time for more than 1 second. After a beep sound, the child lock function is released.
If the START/PAUSE button is not
pushed, the washing machine will
automatically switch off the power
after 5 minutes.
RESERVE/REMAIN time indicator digitron
During sensing, it displays --
During reserve procedure, it displays the remained reserve time (in
hours)
During operation of programs, it displays the remained time (minutes).
If the remained time exceeds 99 minutes, it adopts A at tens place to
represent 100 minutes, b to represent 110 minutes. For instance, A3
represents 103 minutes.
In case of abnormal phenomenon, it displays
the abnormal symbol (see to Page 16)
Page16
POWER
ON/OFF
Time remained
(minutes)
START
PAUSE
STA
RT/P
AUSE
button
Reserve
(hours later)
After the power is switched on, push it to Start the machine
During working, push it to pause working.
During pause, push it to resume working.
PROGRAM
lection button
PROGRAM se
WATER LEVEL
Following automatic programs are available for selection
RESERVE/CALEFACTION
Applicable situation
Common washing
PROGRAM
STANDARD
QUICK
Quick and high-efficiency wash for
common
Super quick wash of the laundry under 1 kg
with light soil
POSTHASTE
JEAN
"RESERVATION/CALEFACTION" button
Washing the relatively big and thick laundries
Washing the chemical fiber laundries
Washing the cotton textiles
Press "RESERVATION/CALEFACTION"button to set
reservation or heating Function.
FIBER
During machine running, thedigitron indicates the cycle
remaining time in minutes). Press "RESERVATION
/CALEFACTION"button, the digitron willIndicate the
remaining reserved time tocycle end (in hours).Thedigitron
will indicate the runningstate of the machine.
COTTON
WOOLLEN
SILK
Washing the woolen textiles
Washing the textile
Heating function can beselected if keep pressing
"RESERVATION/CALEFACTION"Button for morethan 2 s.
If the decimal pointof digitron is lighted,it means heating
WATER LEVEL
butto
n
The washing machine can detect the laundries automatically.
After detection, it will set the water level to suitable value among 4, 6,
8, and 10 automatically.
You can also set water level by yourself. After the machine is started,
it will not set water level automatically. You shall push the
start/pause button to make new setting.
If there's water inside the tub, the machine cannot detect the
laundries and will display water level 6 .
If wet laundries are put in, it may display water level 10 . You must
set suitable water level by yourself.
function is selected.The initial temperature isabout 30
and you can selectyour desired value ina switching
,
sequence 30
40
off 20 . If keep pressingthe
"RESERVATION/CALEFACTION" button formore than 2 s
again, the temperature indicatorturns off, andthe
Reservation can be selected, you can selectreserved time.
After the machine startsrunning, if selection orcancellation
of heating function isdesired, you should switchoff the power
and reselect.
If POSTHASTE programs selected, it will display water level 3 .
When water level 2 is reached in water filling, it will perform
washing while filling water. When water level 3 is reached, it will
change to normal washing.
During operation of wash and rinse program, you can push down
the water level button to add water. When you release the button, or
it reaches the overflow water level, the machine will stop adding
water.
Steps of using the operation buttons and description of the steps
b
POWER
ON/OFF
Times
Time remained
(Minute)
START
PAUSE
SOAK
PROGRAM
WASH
RINSE
WATER LEVEL
SPIN RESERVE/
1 Push the "POWER ON/OFF " button to switch on the power.
POWER
ON/OFF
2 Push the "PROGRAM" button to select suitable automatic program.
PROGRAM
After switching on the power, the machine will set "STANDARD " program automatically. To select
other automatic program, push the "PROGRAM" button till the relative indicator is on. Refer to the
"PROGRAM" button on Page 11 for the selection.
Page 11
For instance: select "POSTHASTE" program for laundries with small
quantity and light soil.
In selecting the ••••••••program, the machine
will execute fuzzy program to select water and wash
time according to the cloth and weight of the
laundries. The full procedure is controlled
automatically.
FIBER
STANDARD
QUICK
COTTON
WOOLLEN
SILK
POSTHASTE
JEAN
3 Push the "SOAK", "WASH", "RINSE" OR "SPIN" button to select suitable procedure.
Minutes
Minutes
SOAK
WASH
RINSE
SPIN
After switching on the power, the washing machine will set to common
program including"wash, rinse,spin "automatically. To select other
procedures, push the "SOAK", " WASH", " RINSE" or "SPIN" button
to select the time of soak, wash and spin, and the times of rinse. After
switching on the power, if you push one of the button among "WASH",
"RINSE"and"SPIN", the digitron of the former procedures will turn off
automatically. The former procedures will not run. For instance: after
switching on the power. If you push the "SPIN"button first, it will execute
spin singly after starting.
Attention
Even there's no water in the tub, a certain period is
required before spin starting.
Do not use the soak program for the woolen textiles.
Separate the laundries that are not colorfast from
other laundries in washing.
The pulsator will not rotate unless the water is
filled to"3" water level.
The soak procedure can work in cooperation with automatic programs like standard, jeans,
fiber and cotton. There is intermittent pulsator stirring during soak.
After the machine starts operation, you can only set the program and procedure during
washing, and can not make setting in other cases.
Press " WATER LEVEL "button,
select suitable water level
WATER
LEVEL
After switching on the power, the washing machine will execute fuzzy program automatically to
detect the cloth. After defection, it can set the water level automatically. To select other water
level, first push the "START/PAUSE"button, then push the "WATER LEVEL" button to set the
water level. Refer to "water level button"in Page 11 for selection.
Page 11
Push the "RESERVE/CALEFACTION "button to select suitable
reserve wash program
RESERVE/CALEFACTION
After switching on, the washing machinereserved wash programwill be automaticallyset
inactive. If youdesire a wash cycle to endat a reservedtime, you canpress the
"RESERVATION/CALEFACTION" button to set a reserved wash program.
Refer to The button of "RESERVATION/CALEFACTION" on page 11.
Page 11
Confirm the reserveprogram
When "RESERVATION" becomesactive, the nixie tube displays the time
to the end of the reserved wash cycle, and the indicator turns on.
To change the running program or cancel the reservation,
you should cut off the supplyand reselect.
the washing will finish
about 18 hours later
Confirm the heating function
Keep pressing the"RESERVATION/CALEFACTION" button for more than 2 s,
the heating indicator turns on (red).
Keep pressing the "RESERVATION/CALEFACTION"button for morethan 2 sagain, the
heating indicator turnsoff and heatingfunction is cancelled.
After the machinestarts running, ifselection or cancellationof heating function
is desired, youshould switch offthe power andreselect.
6.Push the "START/PAUSE " button
START
PAUSE
5 Close the lop lid
6 Finish washing
As the top lid opened, the Washer will automatically give an alarm
and stop running, exclusively during supplying water and rinsing.
After finishing wash , it will alarm
automatically.
7.Disposal after washing
After using, please clean the lint and foreign materials of the lint filter etc. in time. Otherwise it may
influence your using the machine.
Please first pull off the power plug from the receptacle before cleaning.
The lint filter must be used during washing.
It must be cleaned in time after each using
Clean the detergent box and set it on
the control panel seat.
1.The method of dismantle : Push it up aslant and gently.
2.The method of install : install it upwards and aslant
and push it in .
Lint filter:
1.Rotate the inner tub with hand till the lint filter reaches
the position convenient for you to take it off. Pull it up to
dismount.
2.Push it down to install.
3.Clean the filter screen after washing.
Dismantle
Dismantle
Install
Install
Dismantle
Install
The filter screen of the water inlet valve is likely to be
blocked by foreign materials and influence the water
inlet.
If the cabinet is dirty, wipe it with wet cloth
Do not flush it directly with water.
Wipe it with neutral detergent.
Please clean it with brush every two months.
Do not wipe it with thinner, petrol, alcohol etc.
1.After washing, close the water faucet. ( If needed, you can dismantle the water inlet hose).
2.Do not store water in the washing machine for a long period. Drain the water completely after each using.
3.Be sure to pull off the power plug before maintenance.
4.Hang up the power cord and drain hose.
5.Wipe off the water drops on the surface of the machine and inside the tub. Open the top lid for some time (
about 1 hour), then close the top lid.
Trouble-shooting Answer to question
(If there's breakdown, please pull off the power plug before checking) The following phenomena are not breakdowns
sometimes. Please confirm again before sending it to repair. If there are real breakdowns, please come to the special
maintenance department or after-sale service department of our company. Do not repair it by yourself.
Phenomenan
The reason
The top lid is opened during reserve
procedure.
How to settle
The digitron displays E0.
Close the top lid.
Put down the drain hose. Open and close the
top lid once.
The drainage cannot work, or is too slow.
The digitron displays E1.
Is the drain hose put down?
Is the drain hose blocked?
Clean the foreign material. Open and close
the top Lid Once.
Close the top lid.
It stops running in midway. The digitron
displays E2.
The top lid is not closed.
Reorder the laundries. Close the top lid.
The machine will start running after 10
seconds of being placed horizontally.
The safety switch acts, and the
spinning cannot work. The
digitron displays E3.
Are the laundries put slantingly?
Is the machine slanting?
Is the water tap opened, or is there water
supply failure?
Is the water inlet valve blocked?
Is the water pressure too low?
The water filling does not work, or is
slow. After about 40 minutes later,
the digital displays E4.
Open the water tap. Push the Start/Pause
button once.
Clean the water inlet valve then push
the Start/Pause button once.
Push the Start/Pause button once.
Please contact the after-sales service department.
The digitron displays E5.
The digitron displays E6.
The temperature sensor is fallen.
The water level sensor is bad.
Please contact the after-sales service department.
The water level drops to the replacement
point after it has supplied water for 2 times
during the whole process.
The digitron displays F5.
Open and close the top lid once.
Please use it when there's power supply.
Insert the power plug tightly.
Fill water to the preset position.
Is there power failure?
Not wash
The machine does
not act
Is the power plug inserted tightly?
Is the water level reached preset position?
Is the power plug inserted tightly?
Is the top lid closed reliably?
Are the laundries set flat?
Insert the power plug tightly.
Close the top lid.
Set the laundries flat.
Adjust the machine to be even
Reorder the laundries and close the top lid.
Remove the foreign materials.
Not spin
Is the machine slanting?
Are the laundries put slantingly in spinning?
Are there any foreign materials?
There's abnormal sound
inside the machine
Is the screw of the jointer of water
inlet hose loose or awry?
The water tap leaks
Fasten the screw of the jointer properly.
Common phenomena
Phenomena
Explanation
* Balance the laundries to avoid slanting.
* The spinning is intermittent when it starts.
* The cloth sensor is detecting the cloth. It will start
adding water after about 48 seconds.
* The wash procedure pauses.
* The program is setting the drain time. A certain
period is needed before it starts spinning.
* Select "SPIN" program, but it does not work.
* The pusaltor pauses during washing , rinsing or
adding water.
* It is to avoid splashing during water filling.
* It is the water remained in the performance
inspection by the factory.
* There may be some water flowing out of the
drain hose in the first use of the machine.
*
It is the special resume function. In the case of power
failure or the power plug is loose during washing, the
machine can save the running program, and resume
the program after the power supply is recobered. You
do not need to set the program again.
*
When the power plug is inserted,computer
board indicator is switched on,and the machine
starts working.
* This is the normal phenomenon .The actual heating
temperature is also influenced by the atmosphere
temperature the water temperature for wash and the
water hardness.
* The actual heating temperature may have
discrepancy with the setting level.
Packing list
Name
Quantity
Storage position
Inside the document bag
One
User's manual
Warranty manual
Inside the document bag
One
Components of the water inlet hose
The end connecting to thewashing machine
Jointer connecting the water
inlet hose and the waterfaucet
One
One
Inside the accessory bag
The end connecting to thewater
inlet hose jointer
Water inlet hose (1 piece)
Water inlet hose joint (1 piece)
Between the upper cushion of the
washing machine package and the
upper seal of the package carton
Bottom plate
Eight
One
Tapping screws
Inside the accessory bag
Inside the accessory bag
Inner cover component
Fuzzy Computerized
Automatic Washing
Machine
One
Specification
Rated washing / spinning capacity
Water level/Water quantity (about)
6.0kg/6.0kg
1/12L 2/16L 3/20L 4/25L 5/29L
6/33L 7/38L 8/42L 9/47L 10/50L
Injection pressure
0.03MPa~0.78MPa
|