Iiyama Computer Monitor B1702S User Manual

USER MANUAL  
ENGLISH  
EGIH  
DEUTSCH  
FRANCAIS  
NEDERLANDS  
Thank you very much for choosing the  
iiyama LCD monitor.  
We recommend that you take a few  
minutes to read carefully through this  
brief but comprehensive manual before  
installing and switching on the monitor.  
Please keep this manual in a safe place  
for your future reference.  
 
FCC DECLARATION OF CONFORMITY  
Model Number:  
Trade Name:  
PL1702 / PL1702W  
iiyama  
Responsible party:  
Address:  
Ampronix Inc.  
8697 Research Dr. Irvine, CA.92618 U.S.A.  
949-788-9930  
Telephone number:  
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)  
This device may not cause harmful interference, and (2) this device must accept any interference received,  
including interference that may cause undesired operation.  
This device has been tested and found to comply with the limits for Class B Personal Computers and  
peripherals, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection  
against harmful interference when the device is operated in a residential environment. This device generates,  
uses and can radiate radio frequency energy, and if not installed and used in accordance with the instructions,  
may cause harmful interference to radio communications. However, there is no guarantee that interference  
will not occur in a particular installation. If you determine the device does cause harmful interference to radio  
or television reception (this may be determined by monitoring the interference while turning the device off and  
on), you are encouraged to try to correct the interference by one of the following measures:  
Reorient or relocate the receiving antenna.  
Increase the separation between the device and receiver.  
Connect the device into an outlet on a circuit different from that to which the receiver  
is connected.  
Consult the dealer or an experienced radio or TV technician for help.  
To meet the FCC requirements, you should use a signal cable with ferrite core at both ends.  
CAUTION  
Changes or modifications not expressly approved by iiyama could void the users authority  
to operate the device under FCC compliance regulations.  
CANADIAN DEPARTMENT OF COMMUNICATIONS COMPLIANCE  
STATEMENT  
This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as  
set out in the radio interference regulation of the Canadian department of communications.  
CE MARKING DECLARATION OF CONFORMITY  
This LCD monitor complies with the requirements of the EC Directive 89/336/EEC “EMC Directive” and 73/23/  
EEC “Low Voltage Directive” as amended by Directive 93/68/EEC.  
The electro-magnetic susceptibility has been chosen at a level that gives correct operation in residential areas,  
business and light industrial premises and small-scale enterprises, inside as well as outside of the buildings.  
All places of operation are characterised by their connection to the public low voltage power supply system.  
We reserve the right to change specifications without notice.  
All trademarks used in this user manual are the property of their respective owners.  
As an ENERGY STAR® Partner, iiyama has determined that this product meets the ENERGY STAR® guidelines for  
energy efficiency.  
 
TABLE OF CONTENTS  
FOR YOUR SAFETY ......................................................................................................................... 1  
SAFETY PRECAUTIONS ............................................................................................................ 1  
SPECIAL NOTES ON LCD MONITORS ........................................................................................ 3  
CUSTOMERSERVICE ................................................................................................................. 3  
CLEANING .................................................................................................................................. 3  
BEFOREYOU OPERATETHE MONITOR ........................................................................................... 4  
FEATURES .................................................................................................................................. 4  
CHECKINGTHE CONTENTS OFTHE PACKAGE ........................................................................ 5  
FITTINGAND REMOVAL OF BASE : ProLite E1702S / E1702SV / E1702WS / E1702WSV ..... 6  
CONTROLSAND CONNECTORS : ProLite E1702S / E1702SV / E1702WS / E1702WSV ........ 7  
CONTROLSAND CONNECTORS : ProLite B1702S ................................................................... 8  
CONNECTING YOUR MONITOR : ProLite E1702S / E1702SV / E1702WS / E1702WSV .......... 9  
CONNECTING YOUR MONITOR : ProLite B1702S ..................................................................... 10  
COMPUTERSETTING .................................................................................................................. 11  
ADJUSTING THE VIEWINGANGLE : ProLite E1702S / E1702SV / E1702WS / E1702WSV ..... 11  
ADJUSTING THE HEIGHTAND THE VIEWINGANGLE : ProLite B1702S ................................... 12  
PANELROTATION : ProLite B1702S .......................................................................................... 12  
OPERATINGTHEMONITOR .............................................................................................................. 13  
ADJUSTMENTMENUCONTENTS ............................................................................................... 14  
SCREENADJUSTMENTS ............................................................................................................ 22  
POWER MANAGEMENTFEATURE ............................................................................................. 25  
TROUBLE SHOOTING ....................................................................................................................... 26  
APPENDIX ......................................................................................................................................... 28  
SPECIFICATIONS : ProLite E1702S ............................................................................................ 28  
SPECIFICATIONS : ProLite E1702SV .......................................................................................... 29  
SPECIFICATIONS : ProLite E1702WS ......................................................................................... 30  
SPECIFICATIONS : ProLite E1702WSV ...................................................................................... 31  
SPECIFICATIONS : ProLite B1702S ............................................................................................ 32  
DIMENSIONS : ProLite E1702S / E1702SV ................................................................................ 33  
DIMENSIONS : ProLite E1702WS / E1702WSV .......................................................................... 33  
DIMENSIONS : ProLite B1702S................................................................................................... 33  
COMPLIANTTIMING .................................................................................................................... 34  
CONNECTORPINASSIGNMENT ................................................................................................. 35  
Regulatory information : The high efficiency LCD backlights used in this  
product contains 5mg or less of Mercury, the disposal of which may be  
regulated due to environmental considerations.  
For disposal or recycling information, please contact your local authorities or  
the Electronic Industries Alliance (www.eiae.org).  
This information is only for U.S.A..  
We recommend recycling of used product. Please contact your dealer or iiyama service  
center. Recycle information is obtained via the Internet, using the address:  
You can access the Web page of different countries from there.  
 
FOR YOUR SAFETY  
SAFETY PRECAUTIONS  
WARNING  
STOP OPERATING THE MONITOR WHEN YOU SENSE TROUBLE  
If you notice any abnormal phenomena such as smoke, strange sounds or fumes, unplug the monitor  
and contact your dealer or iiyama service center immediately. Further use may be dangerous and  
can cause fire or electric shock.  
NEVER REMOVE THE CABINET  
High voltage circuits are inside the monitor. Removing the cabinet may expose you to the danger of  
fire or electric shock.  
DO NOT PUT ANY OBJECT INTO THE MONITOR  
Do not put any solid objects or liquids such as water into the monitor. In case of an accident, unplug  
your monitor immediately and contact your dealer or iiyama service center. Using the monitor with  
any object inside may cause fire, electric shock or damage.  
INSTALL THE MONITOR ON A FLAT, STABLE SURFACE  
The monitor may cause an injury if it falls or is dropped.  
DO NOT USE THE MONITOR NEAR WATER  
Do not use where water may be splashed or spilt onto the monitor as it may cause fire or electric  
shock.  
OPERATE UNDER THE SPECIFIED POWER SUPPLY  
Be sure to operate the monitor only with the specified power supply. Use of an incorrect voltage will  
cause malfunction and may cause fire or electric shock.  
PROTECT THE CABLES  
Do not pull or bend the power cable and signal cable. Do not place the monitor or any other heavy  
objects on the cables. If damaged, the cables may cause fire or electric shock.  
ADVERSE WEATHER CONDITIONS  
It is advisable not to operate the monitor during a heavy thunder storm as the continual breaks in  
power may cause malfunction. It is also advised not to touch the plug in these circumstances as it  
may cause electric shock.  
FOR YOUR SAFETY  
1
 
CAUTION  
INSTALLATION LOCATION  
Do not install the monitor where sudden temperature changes may occur, or in humid, dusty or smoky  
areas as it may cause fire, electric shock or damage. You should also avoid areas where the sun  
shines directly on the monitor.  
DO NOT PLACE THE MONITOR IN A HAZARDOUS POSITION  
The monitor may topple and cause injury if not suitably located. Please also ensure that you do not  
place any heavy objects on the monitor, and that all cables are routed such that children may not pull  
the cables and possibly cause injury.  
MAINTAIN GOOD VENTILATION  
Ventilation slots are provided to keep the monitor from overheating. Covering the slots may cause  
fire. To allow adequate air circulation, place the monitor at least 10 cm (or 4 inches) from any walls.  
Do not remove the tilt stand when operating the monitor. Ventilation slots on the back of the cabinet  
will be blocked and the monitor may overheat if the stand is removed. This may cause fire or damage.  
Operating the monitor on its back, side, upside down or on a carpet or any other soft material may  
also cause damage.  
DISCONNECT THE CABLES WHEN YOU MOVE THE MONITOR  
When you move the monitor, turn off the power switch, unplug the monitor and be sure the signal  
cable is disconnected. If you do not disconnect them, it may cause fire or electric shock.  
UNPLUG THE MONITOR  
If the monitor is not in use for a long period of time it is recommended that it is left unplugged to avoid  
accidents.  
HOLD THE PLUG WHEN DISCONNECTING  
To disconnect the power cable or signal cable, always pull it by the plug. Never pull on the cable itself  
as this may cause fire or electric shock.  
DO NOT TOUCH THE PLUG WITH WET HANDS  
Pulling or inserting the plug with wet hands may cause electric shock.  
WHEN YOU INSTALL THE MONITOR ON YOUR COMPUTER  
Be sure the computer is strong enough to hold the weight of the monitor, otherwise, you may damage  
your computer.  
DO NOT PUT FLOPPY DISKS NEAR THE SPEAKERS  
Magnetically recorded data, such as on a floppy disk, may become corrupted by the magnetic field  
produced by the speakers if the disks are placed on or near the speakers.  
OTHERS  
ERGONOMIC RECOMMENDATIONS  
To eliminate eye fatigue, do not operate the monitor against a bright background or in a dark room. For  
optimal viewing comfort, the monitor should be just below eye level and 40-60 cm (16-24 inches)  
away from your eyes. When using the monitor over a prolonged time, a ten minute break every hour  
is recommended as looking at the screen continuously can cause eye strain.  
2
FOR YOUR SAFETY  
 
SPECIAL NOTES ON LCD MONITORS  
The following symptoms are normal with LCD monitors and do not indicate a problem.  
When you first turn on the LCD monitor, the picture may not fit in the display area  
because of the type of computer that is used. In this case, adjust the picture  
position to the correct position.  
NOTE  
Due to the nature of the backlight, the screen may flicker during initial use. Turn off  
the Power Switch and then turn it on again to make sure the flicker disappears.  
You may find slightly uneven brightness on the screen depending on the desktop  
pattern you use.  
Due to the nature of the LCD screen, an afterimage of the previous screen may  
remain after switching the image, when the same image is displayed for hours. In  
this case, the screen is recovered slowly by changing the image or turning off the  
Power Switch for hours.  
Contact your dealer or iiyama service center for the backlight replacement when the  
screen is dark, flickering or not lighting up. Never attempt to replace it by yourself.  
CUSTOMER SERVICE  
The fluorescent light used in the LCD monitor may have to be periodically replaced.  
For the warranty coverage on this component, please check with local iiyama  
service center.  
NOTE  
If you have to return your unit for service and the original packaging has been  
discarded, please contact your dealer or iiyama service center for advice or  
replacement packaging.  
CLEANING  
WARNING  
If you drop any materials or liquids such as water into the monitor when cleaning,  
unplug the power cable immediately and contact your dealer or iiyama service center.  
CAUTION  
For safety reasons, turn off the power switch and unplug the monitor before you  
clean it.  
NOTE To protect the LCD panel, do not scratch or rub the screen with a hard object.  
Never use any of the following strong solvents. These will damage the cabinet and  
the LCD screen.  
Spray-type cleaner  
Wax  
Thinner  
Benzine  
Acid or Alkaline solvent  
Abrasive cleaner  
Touching the cabinet with any product made from rubber or plastic for a long time  
may cause degeneration or loss of paint on the cabinet.  
Stains can be removed with a cloth lightly moistened with a mild detergent solvent. Then  
wipe the cabinet with a soft dry cloth.  
CABINET  
LCD  
Periodic cleaning with a soft dry cloth is recommended.  
SCREEN  
Don't use tissue paper etc. because these will damage the LCD screen.  
FOR YOUR SAFETY  
3
 
BEFORE YOU OPERATE THE MONITOR  
[Stopper] : ProLite B1702S  
Please stand the monitor and then remove the  
stopper on the back of the stand slowly.  
FEATURES  
43cm (17") TFT Color LCD Monitor  
Supports Resolutions up to 1280 × 1024 : ProLite E1702S / E1702SV / B1702S  
Supports Resolutions up to 1440 × 900 : ProLite E1702WS / E1702WSV  
High Contrast 1000:1 / High Brightness 300cd/m2 / Quick Response Time 2ms  
(Gray to Gray): ProLite E1702S-1 / E1702SV-1 / B1702S-1  
High Contrast 1000:1 / High Brightness 300cd/m2 :  
ProLite E1702S-2 / E1702SV-2 / B1702S-2  
High Contrast 600:1 / High Brightness 250cd/m2 : ProLite E1702WS / E1702WSV  
Multi-Color Control  
Supports sRGB International Standard  
Gamma Control  
Clear Display for Moving Pictures & Photographs  
Digital Character Smoothing  
Automatic Set-up  
Stereo Speakers  
2 × 1W Stereo Speakers  
Economy Mode  
Reduced Power Consumption  
Plug & Play VESA DDC2B Compliant  
Windows® 95/98/2000/Me/XP/Vista Compliant  
DDC/CI Compliant  
Power Management (ENERGY STAR® and VESA DPMS Compliant)  
Ergonomic Design  
TCO ’03 and TÜV-ErgonomicsApproved  
Digital Input (DVI-D, HDCP Compliant) for Clear Display :  
ProLite E1702S / E1702WS  
90° Panel Rotation Design : ProLite B1702S  
VESA Mounting Standard (100mm×100mm) Compliant  
4
BEFORE YOU OPERATE THE MONITOR  
 
CHECKING THE CONTENTS OF THE PACKAGE  
The following accessories are included in your package. Check to see if they are enclosed with the  
monitor. If anything is missing or damaged, please contact your local iiyama dealer or regional iiyama  
office.  
Power Cable *1  
DVI-D Signal Cable *2  
Stand *3  
D-Sub Signal Cable  
Audio Cable  
Cable Holder  
User Manual  
1
CAUTION  
The rating of the Power Cable enclosed in 120V area is 10A/125V. If you are using  
a power supply higher than this rating, then a power cable with a rating of 10A/  
250V must be used.  
*
However, all guarantees and warranties are void for any problems or damage  
caused by a power cable not supplied by iiyama.  
2
Accessory for ProLite E1702S / E1702WS / B1702S  
*
3
Accessory for ProLite E1702S / E1702SV / E1702WS / E1702WSV  
*
<softOSM>  
The Desktop softOSM software complies with the DDC/CI standard and can be downloaded from the  
iiyama website.  
softOSM Software Functions  
Easy access to the range of user adjustments can be via the softOSM Software rather than the  
buttons located on the display itself.  
The communication between software and display occurs through the Display Cable provided;  
hence no special cabling is required.  
Screen rotation features can also be controlled via the softOSM Software switching on the fly  
between Landscape and Portrait. Please note that a suitable graphics card with adequate  
performance must be used in conjunction with this feature. : Available for ProLite B1702S only.  
Compatible with Windows 98, 2000, XP and Vista.  
BEFORE YOU OPERATE THE MONITOR  
5
 
FITTING AND REMOVAL OF BASE :  
ProLite E1702S / E1702SV / E1702WS / E1702WSV  
CAUTION  
Install the stand on a stable surface. The monitor may cause injury or damage if it  
falls or is dropped.  
Do not give a strong impact to the monitor. It may cause damage.  
Unplug the monitor before installation to avoid electric shock or damage.  
<Install>  
Hold the monitor and push the post down  
into the stand.  
Stand  
<Remove>  
Press the stopper at the back of the stand  
and remove the stand from the post.  
Press the stopper  
6
BEFORE YOU OPERATE THE MONITOR  
 
CONTROLS AND CONNECTORS :  
ProLite E1702S / E1702SV / E1702WS / E1702WSV  
<Front>  
Menu Button (MENU)  
<Back>  
A
B
C
D
E
F
+ Button (  
)
Power Switch (  
– Button (  
)
)
Auto Button (AUTO)  
Power Indicator  
Blue:  
Normal operation  
NOTE  
Orange: Power Management  
Auto (Signal Select)  
When no signal is received from the system, the display enters into its  
Power Management Mode reducing power consumption to < than 2W.  
Analog / Digital (Signal Select)  
The monitor enters into power management mode which reduces the power  
consumption to less than 2W when receiving no horizontal and/or vertical  
sync signal.  
Speakers  
G
H
I
J
AC Connector (AC IN)  
Audio Connector (  
)
DVI-D 24pin Connector (DVI-D)*  
K D-sub mini 15pin Connector (D-SUB)  
L Keyhole for Security Lock  
You can fasten a security lock and cable to prevent the monitor from being removed  
without your permission.  
NOTE  
Available for ProLite E1702S / E1702WS only.  
*
BEFORE YOU OPERATE THE MONITOR  
7
 
CONTROLS AND CONNECTORS : ProLite B1702S  
<Front>  
Menu Button (MENU)  
<Back>  
A
B
C
D
E
F
+ Button (  
)
Power Switch (  
– Button (  
)
)
Auto Button (AUTO)  
Power Indicator  
Blue:  
Normal operation  
NOTE  
Orange: Power Management  
Auto (Signal Select)  
When no signal is received from the system, the display enters into its  
Power Management Mode reducing power consumption to < than 2W.  
Analog / Digital (Signal Select)  
The monitor enters into power management mode which reduces the power  
consumption to less than 2W when receiving no horizontal and/or vertical  
sync signal.  
Speakers  
G
H
I
J
AC Connector (AC IN)  
Audio Connector (  
)
DVI-D 24pin Connector (DVI-D)  
K D-sub mini 15pin Connector (D-SUB)  
L Keyhole for Security Lock  
You can fasten a security lock and cable to prevent the monitor from being removed  
without your permission.  
NOTE  
8
BEFORE YOU OPERATE THE MONITOR  
 
CONNECTING YOUR MONITOR :  
ProLite E1702S / E1702SV / E1702WS / E1702WSV  
Ensure that both the computer and the monitor are switched off.  
A
B
Connect the computer to the monitor with the signal cable. (See page 35 for CONNECTOR PIN  
ASSIGNMENT.)  
Connect the monitor to the audio equipment with the Audio Cable when using the audio features.  
C
D Connect the Power Cable to the monitor first and then to the power supply.  
NOTE The signal cables used for connecting the computer and monitor may vary with the type of  
computer used. An incorrect connection may cause serious damage to both the monitor and  
the computer. The cable supplied with the monitor is for a standard 15 pin D-Sub connector.  
If a special cable is required please contact your local iiyama dealer or regional iiyama office.  
For connection to Macintosh computers, contact your local iiyama dealer or regional  
iiyama office for a suitable adaptor.  
Make sure you tighten the finger screws at each end of the signal cable.  
[Example of Connection]  
<Back>  
Power Cable  
(Accessory)  
D-Sub Signal Cable  
(Accessory)  
DVI-D Signal Cable*  
Audio Cable (Accessory)  
Computer  
Available for ProLite E1702S / E1702WS only.  
*
[ Fitting of Cable Holder ]  
Collect cables at the back of the stand.  
A
B
Ãáâìå Èïìäåò  
Position the Cable Holder at the base of the  
stand column by inserting the ‘tabs’ into the  
guide holes. Apply gentle pressure downwards  
to secure.  
Stand  
[ Removal of Cable Holder ]  
Remove Cable Holder by sliding up the base  
column.  
A
BEFORE YOU OPERATE THE MONITOR  
9
 
CONNECTING YOUR MONITOR : ProLite B1702S  
Ensure that both the computer and the monitor are switched off.  
A
B
Connect the computer to the monitor with the signal cable. (See page 35 for CONNECTOR PIN  
ASSIGNMENT.)  
Connect the monitor to the audio equipment with the Audio Cable when using the audio features.  
C
D Connect the Power Cable to the monitor first and then to the power supply.  
NOTE The signal cables used for connecting the computer and monitor may vary with the type of  
computer used. An incorrect connection may cause serious damage to both the monitor and  
the computer. The cable supplied with the monitor is for a standard 15 pin D-Sub connector.  
If a special cable is required please contact your local iiyama dealer or regional iiyama office.  
For connection to Macintosh computers, contact your local iiyama dealer or regional  
iiyama office for a suitable adaptor.  
Make sure you tighten the finger screws at each end of the signal cable.  
[Example of Connection]  
<Back>  
D-Sub Signal Cable  
(Accessory)  
Power Cable  
(Accessory)  
DVI-D Signal Cable  
(Accessory)  
Audio Cable (Accessory)  
Computer  
[ Fitting of Cable Holder ]  
Collect cables at the back of the stand.  
A
B
Inserting the tabs of the Cable Holder into guide  
holes of the stand.( )  
B
Place the Cable Holder by inserting the tabs of  
the Cable Holder into guide holes of the  
C
stand.(  
)
C
[ Removal of Cable Holder ]  
Push the both sides and tilt back the Cable  
Holder.  
A
10 BEFORE YOU OPERATE THE MONITOR  
 
COMPUTER SETTING  
Signal Timing  
Change to the desired signal timing listed on page 34: COMPLIANT TIMING.  
Windows 95/98/2000/Me/XP/Vista Plug & Play  
The iiyama LCD monitor complies with DDC2B of VESA standard. The Plug & Play function runs on  
Windows 95/98/2000/Me/XP/Vista by connecting the monitor to DDC2B compliant computer with  
the Signal Cable supplied. Windows 95/98/2000/Me/XP Monitor Information File for iiyama monitors  
may be necessary for your computer and obtained via the Internet, using the address:  
For additional information on how to download the driver for your monitor, please  
NOTE  
access one of the internet sites noted above.  
Monitor Drivers are not required in most cases for Windows Vista, Macintosh or Unix  
operating systems. For further information, please contact your computer dealer first  
for advice.  
ADJUSTING THE VIEWING ANGLE :  
ProLite E1702S / E1702SV / E1702WS / E1702WSV  
For optimal viewing it is recommended to look at the full face  
of the monitor.  
Hold the stand so that the monitor does not topple when you  
change the monitor’s angle.  
You are able to adjust the monitor’s angle up to 20 degrees  
upward, 5 degrees downward.  
In order to ensure a healthy and relaxed body position when  
20  
using the monitor at visual display workstations, it is  
recommended that the adjusted tilt angle should not exceed  
5
10 degrees. Adjust the monitor’s angle to your own preference.  
NOTE Do not touch the LCD screen when you change the  
angle. It may cause damage or break the LCD screen.  
Careful attention is required not to catch your fingers  
or hands when you change the angle.  
BEFORE YOU OPERATE THE MONITOR 11  
 
ADJUSTING THE HEIGHT AND THE VIEWING ANGLE : ProLite B1702S  
For optimal viewing it is recommended to look at the  
full face of the monitor, then adjust the monitor's  
Height and angle to your own preference.  
Hold the stand so that the monitor does not topple  
110mm  
when you change the monitor’s angle.  
you are able to adjust the monitor's height up to  
110mm,angle up to 35degrees right and left,25  
degrees upward,5 degrees downward.  
NOTE Do not touch the LCD screen when you  
change the angle. It may cause damage or  
break the LCD screen.  
Careful attention is required not to catch  
your fingers or hands when you change  
the angle.  
PANEL ROTATION : ProLite B1702S  
Ajust the monitor's height to the maximum.  
Rotate the panel 90 degrees.  
A
B
Portrait: Turn clockwise.  
Landscape: Turn counter clockwise.  
Attempting to rotate without fully  
extending upward may cause  
damage to stand.  
NOTE  
Screen Rotation should be  
accessed via the softOSM  
software.  
Ajust the monitor's angle to your preference.  
C
12 BEFORE YOU OPERATE THE MONITOR  
 
OPERATING THE MONITOR  
To create the best picture, your iiyama LCD monitor has been preset at the factory with the COMPLIANT  
TIMING shown on page 34. You are also able to adjust the picture by following the button operation  
shown below. For more detailed adjustments, see page 22 for SCREEN ADJUSTMENTS.  
Press the Menu Button to start the On Screen Display feature. There are  
additional Menu pages which can be switched by using the +/– Buttons.  
Displayed while sRGB is active.  
Displayed while Lock Out is active.  
Displayed while Mute is active.  
Displayed while Economy Mode is active.  
Page no.  
1
sRGB  
LOCK  
Menu:1  
Adjustment icon  
Current horizontal frequency,  
vertical refresh rate  
and resolution  
1280 × 1024  
H : 8 0 . 0 K H z V : 7 5 . 0 H z  
Select the Menu page which contains the adjustment icon relating to the  
adjustment you want to make. Press the Menu Button again. Then, use the  
+/– Buttons to highlight the desired adjustment icon. Press the Menu Button  
again.  
B
C
Use the +/– Buttons to make the appropriate adjustment or setting.  
For example, to correct for vertical position, select Menu page number 1 and then press the Menu  
Button. Then, select  
(V-Position) by using the +/– Buttons.  
Menu:1  
1280 × 1024  
H : 8 0 . 0 K H z V : 7 5 . 0 H z  
An adjustment scale appears after you press the Menu Button. Use the +/– Buttons to change the  
vertical position settings. The vertical position of the overall display should be changing accordingly  
while you are doing this.  
V-Position  
The bar shows  
the progress of the  
+
50  
adjustment being made.  
NOTE  
When button operations are aborted during adjustment, On-Screen Display disappears when the  
time set for the OSD Off Timer has passed. The Auto Button can be used to exit OSD window  
immediately.  
Any changes are automatically saved in the memory when the On Screen Display disappears.  
Turning off the power should be avoided while using the Menu.  
Adjustments for Clock, Phase and Position are saved for each signal timing. Except for these  
adjustments, all other adjustments have only one setting which applies to all signal timings.  
OPERATING THE MONITOR 13  
 
ADJUSTMENT MENU CONTENTS  
Direct  
You can skip the Menu pages and display an adjustment scale directly by using the  
following button operations.  
Brightness / Contrast / Volume: To display direct menu press either of the +/- Buttons. Continue  
to use the +/- Buttons to select the adjustments required.  
Auto Set-up:  
Press the Auto Button when the Menu is not displayed.  
Volume (Mute): With the OSD menu off, the pressing and holding of the Menu Button for 1-2  
seconds will enable/disable the Audio Mute facility.  
Signal Select*: With the OSD menu off, pressing and holding the Auto Button for 1-2 seconds will  
switch the input signal from Analogue to Digital.  
Lock Out:  
With the OSD menu off, pressing and holding the Menu and ‘-‘ Buttons  
simultaneously for a period of at least 7 seconds will enable and disable the OSD  
Lock Out mode.  
is displayed while Lock Out is active.  
* Available for ProLite E1702S / E1702WS / B1702S only.  
14 OPERATING THE MONITOR  
 
Analog Input  
Menu : 1  
(Analog)  
Menu:1  
1280 × 1024  
H : 8 0 . 0 K H z V : 7 5 . 0 H z  
Adjustment Item  
Brightness *1  
Problem / Option  
Button to Press  
Too dark  
Direct  
Too bright  
Too dull  
Direct  
Contrast  
Too intense  
Clock *2  
To correct flickering text or lines  
Phase *2  
To correct flickering text or lines  
Too low  
Too high  
V-Position  
H-Position  
Return to Menu  
Too far to the left  
Too far to the right  
Highlight “Menu : 1” again.  
*1 Adjust the Brightness when you are using the monitor in a dark room and feel the screen is too  
bright.  
*2 See page 22 for SCREENADJUSTMENTS.  
See page 14 for Direct adjustment.  
Direct  
OPERATING THE MONITOR 15  
 
Menu : 2  
(Analog)  
Menu:2  
1280 × 1024  
H : 8 0 K H z V : 7 5 . 0 H z  
Adjustment Item  
Problem / Option  
Button to Press  
NO  
Return to Menu.  
Auto Set-up *3  
Adjust Clock, Phase, V-Position and H-Position  
automatically.  
YES  
Direct  
Setting  
Off The Auto Set-up is not performed when the  
signal input is changed.  
Adjust Clock, Phase, V-Position and H-Position  
automatically when the signal input is changed.  
On  
NOTE The brightness of screen varies for several seconds during the adjustment.  
This function is not performed automatically when changing the signal input because  
the factory-preset of “Setting” in Auto Set-up is set to Off.  
1
2
Color 1: 9300K  
Color 2: 7500K  
Color 3: 6500K  
sRGB  
Color Temp.  
3
s
R
G
B
Too weak  
Too strong  
(User)  
NOTE sRGB is an international standard which defines and unifies the difference of color  
appearance between equipment.  
You can not adjust the Gamma and Economy Mode during sRGB mode because those  
settings are locked.  
is displayed while sRGB is active.  
Sharpness  
1 2 3 4 5  
Adjust the picture quality at resolutions of less than 1280 × 1024  
(ProLite E1702S / E1702SV / B1702S), 1440 × 900 (ProLite  
E1702WS / E1702WSV).  
You can change the picture quality from 1 to 5 (sharp to soft).  
Press the + Button to change the picture quality in numerical  
order. Press the – Button to change the picture quality in reverse  
numerical order.  
*3 For best results, use the Auto Set-up in conjunction with the adjustment pattern. See page 22 for  
SCREENADJUSTMENTS.  
See page 14 for Direct adjustment.  
Direct  
16 OPERATING THE MONITOR  
 
Menu : 2  
(Analog)  
Adjustment Item  
Problem / Option  
Off  
Normal  
Gamma  
Mode1  
Mode2  
Off  
High contrast  
Dark  
Normal  
Economy Mode  
Mode1  
Brightness of back-light is reduced.  
Brightness of back-light is reduced more than Mode1.  
Mode2  
NOTE ꢀ  
is displayed while Economy Mode is active.  
Return to Menu  
Highlight “Menu : 2” again.  
OPERATING THE MONITOR 17  
 
Menu : 3  
(Analog)  
Menu:3  
1280 × 1024  
H : 8 0 . 0 K H z V : 7 5 . 0 H z  
Problem / Option  
Button to Press  
Adjustment Item  
Too soft  
Too loud  
Direct  
Volume  
NOTE ꢀ  
is displayed while Mute is active.  
1 2 3 4 5  
OSD Position  
You can move the OSD display area  
to any one of the following 5 positions  
within the overall display:  
Press the + Button to move the OSD in numerical order. Press  
the – Button to move the OSD in reverse numerical order.  
Set the OSD Off Timer for 3-60 seconds.  
OSD Off Timer  
Language  
English  
English  
Español  
Italiano  
Spanish  
Italian  
Deutsch  
German  
Français  
Auto  
French  
Japanese  
Select the signal input automatically.  
Select the Analog input (D-SUB).  
Select the Digital input (DVI-D).  
Signal Select* Direct  
Analog  
Digital  
When both Analogue and Digital cables are connected, you can switch between them  
using the direct access facility described earlier. If only one input is present, this will  
automatically be selected. In Power Management Mode input switching is disabled.  
NOTE  
NO  
Return to Menu.  
Reset  
YES  
Factory-preset data is restored.  
Return to Menu  
Highlight “Menu : 3” again.  
* Available for ProLite E1702S / E1702WS / B1702S only.  
See page 14 for Direct adjustment.  
Direct  
18 OPERATING THE MONITOR  
 
Digital Input : Available for ProLite E1702S / E1702WS / B1702S only.  
Menu:1  
1280 × 1024  
H : 8 0 . 0 K H z V : 7 5 . 0 H z  
Adjustment Item  
Problem / Option  
Button to Press  
Too dark  
Brightness *1  
Direct  
Direct  
Too bright  
Too dull  
Contrast  
Too intense  
1
2
3
s
Color 1: 9300K  
Color Temp.  
Color 2: 7500K  
Color 3: 6500K  
sRGB  
R
G
B
Too weak  
Too strong  
User  
sRGB is an international standard which defines and unifies the difference of color  
appearance between equipment.  
NOTE  
You can not adjust the Gamma and Economy Mode during sRGB mode because those  
settings are locked.  
is displayed while sRGB is active.  
1 2 3 4 5  
Sharpness  
Adjust the picture quality at resolutions of less than 1280  
× 1024 (ProLite E1702S / B1702S), 1440 × 900 (ProLite  
E1702WS).  
You can change the picture quality from 1 to 5 (sharp to soft).  
Press the + Button to change the picture quality in  
numerical order. Press the – Button to change the picture  
quality in reverse numerical order.  
Off  
Normal  
Gamma  
High contrast  
Dark  
Mode1  
Mode2  
*1 Adjust the Brightness when you are using the monitor in a dark room and feel the screen is too  
bright.  
See page 14 for Direct adjustment.  
Direct  
OPERATING THE MONITOR 19  
 
Menu : 1  
(Digital)  
Adjustment Item  
Problem / Option  
Normal  
Off  
Economy Mode  
Mode1  
Mode2  
Brightness of back-light is reduced.  
Brightness of back-light is reduced more than Mode1.  
NOTE ꢀ  
is displayed while Economy Mode is active.  
Return to Menu  
Highlight “Menu : 1” again.  
20 OPERATING THE MONITOR  
 
Menu : 2  
(Digital)  
Menu:2  
1280 × 1024  
H : 8 0 . 0 K H z V : 7 5 . 0 H z  
Problem / Option  
Button to Press  
Adjustment Item  
Too soft  
Too loud  
Direct  
Volume  
NOTE ꢀ  
is displayed while Mute is active.  
1 2 3 4 5  
OSD Position  
You can move the OSD display area  
to any one of the following 5 positions  
within the overall display:  
Press the + Button to move the OSD in numerical order. Press  
the – Button to move the OSD in reverse numerical order.  
Set the OSD Off Timer for 3-60 seconds.  
OSD Off Timer  
Language  
Spanish  
Italian  
English  
English  
Español  
Italiano  
Deutsch  
German  
Français  
Auto  
French  
Japanese  
Select the signal input automatically.  
Select the Analog input (D-SUB).  
Select the Digital input (DVI-D).  
Signal Select  
Direct  
Analog  
Digital  
When both Analogue and Digital cables are connected, you can switch between them  
using the direct access facility described earlier. If only one input is present, this will  
automatically be selected. In Power Management Mode input switching is disabled.  
NOTE  
NO  
Return to Menu.  
Reset  
YES  
Factory-preset data is restored.  
Return to Menu  
Highlight “Menu : 2” again.  
See page 14 for Direct adjustment.  
Direct  
OPERATING THE MONITOR 21  
 
SCREEN ADJUSTMENTS  
Adjust the image by following the procedure below to get the desired picture when selecting Analog input.  
The screen adjustments described in this manual are designed to set image position and minimize  
flicker or blur for the particular computer in use.  
ProLite E1702S / E1702SV / B1702S are designed to provide the best performance at resolution of  
1280 × 1024, but can not provide the best at resolutions of less than 1280 × 1024 because the picture  
is automatically stretched to fit the full screen. It is recommended to operate at resolution of 1280 ×  
1024 in normal use.  
ProLite E1702WS / E1702WSV are designed to provide the best performance at resolution of 1440  
× 900, but can not provide the best at resolutions of less than 1440 × 900 because the picture is  
automatically stretched to fit the full screen. It is recommended to operate at resolution of 1440 × 900  
in normal use.  
Displayed text or lines will be blurred or irregular in thickness when the picture is stretched due to  
the screen enlargement process.  
It is preferable to adjust the image position and frequency with the monitor controls, rather than the  
computer software or utilities.  
Perform adjustments after a warm-up period of at least thirty minutes.  
Additional adjustments may be required after the Auto Set-up depending on the resolution or signal timing.  
The Auto Set-up may not work correctly when displaying the picture other than the screen  
adjustment pattern. In this case, manual adjustments are required.  
There are two ways to adjust the screen. One way is automatic adjustment for Clock, Phase and  
Position. The other way is performing each adjustment manually.  
Perform the Auto Set-up first when the monitor is connected to a new computer, or resolution is  
changed. If the screen has a flicker or blur, or the picture does not fit in the display area after  
performing the Auto Set-up, manual adjustments are required. Both adjustments should be made by  
using the screen adjustment pattern (Test.bmp) obtained via the IIYAMA web site (http://  
www.iiyama.com).  
Adjust the image by following the procedure below to get the desired picture.  
This manual explains adjustment under Windows 95/98/2000/Me/XP/Vista.  
Display the picture at the optimum resolution.  
A
B
Enter the Test.bmp (screen adjustment pattern) to wallpaper.  
Consult the appropriate documentation for doing this.  
NOTE  
Test.bmp is made at resolution of 1280 × 1024. Set the display position to center in the  
wallpaper setting dialogue box. If you use Microsoft® PLUS! 95/98 cancel the setting  
of “Stretch desktop wallpaper to fit the screen”.  
[Adjustment pattern]  
Color bar  
Zebra pattern  
Picture frame  
This is the image  
displayed at 1280 × 1024.  
22 OPERATING THE MONITOR  
 
Press the Auto Button. (Auto Set-up)  
C
D
Adjust the image manually by following procedure below when the screen has a  
flicker or blur, or the picture does not fit in the display area after performing the Auto  
Set-up.  
Adjust the V-Position so that the top and bottom of the picture frame will fit to the  
display area.  
E
+
1) Adjust the H-Position so that the left side of the picture frame will move to the left  
edge of the display area.  
F
+
2) Stretch the right side of the picture frame to the right edge of the display area by  
adjusting the Clock.  
+
When the left side of the picture frame moves apart from the left edge of the display  
NOTE  
area during the Clock adjustment, adjust steps 1) and 2).  
Another way to make the Clock adjustment is to correct the vertical wavy lines in the  
zebra pattern.  
The picture may flicker during the Clock, H-Position and V-Position adjustment.  
In case the picture frame is bigger or smaller than the data display area after the Clock  
adjustment, repeat steps from  
.
C
OPERATING THE MONITOR 23  
 
Adjust the Phase to correct horizontal wavy noise, flicker or blur in the zebra pattern.  
G
+
In case the strong flicker or blurs remain on a part of the screen, repeat steps  
NOTE  
and  
F
because the Clock may not be adjusted correctly. If the flicker or blurs still remain,  
G
set the refresh rate of computer to low (60Hz) and repeat steps from  
again.  
C
Adjust the H-Position after the Phase adjustment if the horizontal position moves  
during the adjustment.  
Adjust the Brightness and Color Temp. to get the desired picture after you complete  
the Clock and Phase adjustments.  
H
Put back your favorite wallpaper.  
24 OPERATING THE MONITOR  
 
POWER MANAGEMENT FEATURE  
The power management feature of this product complies with power saving requirement of ENERGY  
STAR® and VESA DPMS. When activated, it automatically reduces unnecessary power consumption  
of the monitor when your computer is not in use.  
To use the feature, the monitor needs to be connected to a VESA DPMS compliant computer. There  
is a power management step the monitor takes as described below. The power management function,  
including any timer settings is configured by the operating system. Check your operating system  
manual for information on how this can be configured.  
Power Management Mode  
When the H-sync signal / V-sync signal / H and V sync signals from the computer are off, the  
monitor enters into Power Management Mode which reduces the power consumption to less than  
2W. The screen becomes dark, and the power indicator turns to orange. From Power Management  
Mode, the image reappears in several seconds when either the keyboard or the mouse are  
touched again.  
Power Indicator  
NORMAL MODE  
Blue  
POWER MANAGEMENT MODE  
Orange  
POWER  
0
2W  
100%  
CONSUMPTION  
Even when using the power management mode, the monitor consumes electricity. Turn  
off the Power Switch whenever the monitor is not in use, during the night and weekends,  
to avoid unnecessary power consumption.  
NOTE  
It is possible that the video signal from the computer may be on while the H or V sync  
signal is missing. In this instance, the POWER MANAGEMENT feature may not work  
properly.  
OPERATING THE MONITOR 25  
 
TROUBLE SHOOTING  
If the monitor fails to operate correctly, please follow the steps below for a possible solution.  
1. Perform the adjustments described in OPERATING THE MONITOR, depending on the problem you  
have. If the monitor does not get a picture, skip to 2.  
2. Consult the following items if you cannot find an appropriate adjustment item in OPERATING THE  
MONITOR or if the problem persists.  
3.  
If you are experiencing a problem which is not described below or you cannot correct the  
problem, discontinue using the monitor and contact your dealer or iiyama service center for  
further assistance.  
Problem  
Check  
The picture does  
not appear.  
A
(Power indicator  
does not light up.)  
The Power Cable is firmly seated in the socket.  
The Power Switch is turned ON.  
The AC socket is live. Please check with another piece of equipment.  
(Power indicator  
is blue.)  
If the blank screen saver is in active mode, touch the keyboard or the  
mouse.  
Increase the Contrast and/or Brightness.  
The computer is ON.  
The Signal Cable is properly connected.  
The signal timing of the computer is within the specification of the monitor.  
(Power indicator If the monitor is in power management mode, touch the keyboard or the  
is orange.)  
mouse.  
The computer is ON.  
The Signal Cable is properly connected.  
The signal timing of the computer is within the specification of the monitor.  
The Signal Cable is properly connected.  
The screen is not ꢃ  
B
synchronized. The signal timing of the computer is within the specification of the monitor.  
The video output level of the computer is within the specification of the  
monitor.  
The screen The signal timing of the computer is within the specification of the monitor.  
position is not in  
the center.  
C
D
E
The screen is The video output level of the computer is within the specification of the  
too bright or too  
dark.  
monitor.  
The power voltage is within the specification of the monitor.  
The screen is  
shaking.  
The signal timing of the computer is within the specification of the monitor.  
26 TROUBLE SHOOTING  
 
Problem  
No sound.  
Check  
The audio equipment (computer etc.) is ON.  
F
The Audio Cable is properly connected.  
The Volume is turned up.  
The Mute is OFF.  
The audio output level of the audio equipment is within the specification of  
the monitor.  
The audio output level of the audio equipment is within the specification of  
The sound is too  
loud or too quiet.  
G
H
the monitor.  
The Audio Cable is properly connected.  
A strange noise is  
heard.  
TROUBLE SHOOTING 27  
 
APPENDIX  
SPECIFICATIONS: ProLite E1702S  
LCD Panel Driving system  
Size  
a-Si TFT Active Matrix  
Diagonal: 43cm / 17"  
0.264mm H × 0.264mm V  
300cd/m2 (Typical)  
Pixel pitch  
Brightness  
Contrast ratio  
1000 : 1 (Typical)  
Viewable angle Right / Left / Up / Down: 80 degrees each  
Response time  
ProLite E1702S-1: 5ms (Black, white, black), 2ms (Gray to Gray)  
ProLite E1702S-2: 5ms (Black, white, black)  
Approx. 16.7 million maximum  
Display Colors  
Sync Frequency  
Analog: Horizontal 24.0-80.0kHz, Vertical 55-75Hz  
Digital: Horizontal 31.0-80.0kHz, Vertical 55-75Hz  
Dot Clock  
135MHz maximum  
Maximum Resolution  
Input Connector  
Plug & Play  
1280 × 1024, 1.3 MegaPixels  
D-Sub mini 15pin, DVI-D 24pin  
VESA DDC2BTM  
Separate sync: TTL, Positive or Negative  
Input Sync Signal  
Input Video Signal  
Analog: 0.7Vp-p (Standard), 75Ω, Positive  
Digital: DVI (Digital Visual Interface Standard Rev.1.0) compliance  
Input Audio Connector  
Input Audio Signal  
Speakers  
ø 3.5mm mini jack (Stereo)  
0.7Vrms maximum  
1.0W × 2 (Stereo speakers)  
Maximum Screen Size  
Power Source  
337.9mm W × 270.3mm H / 13.3" W × 10.6" H  
100-240VAC, 50/60Hz, 1.5A  
Power Consumption  
Dimensions / Net Weight  
Tilt Angle  
40W maximum, Power management mode: 2W maximum*  
370.5 × 381.5 × 210.0mm / 14.6× 15.0 × 8.3" (W×H×D), 4.1kg / 9.0lbs  
Up: 20 degrees, Down: 5 degrees  
Operating: Temperature 5 to 35°C / 41 to 95°F  
Environmental  
Humidity  
Storage: Temperature -20 to 60°C / -4 to 140°F  
Humidity 5 to 85% (No condensation)  
10 to 80% (No condensation)  
Considerations  
Approvals  
TCO ’03, CE, TÜV-GS, TÜV-Ergonomics, FCC-B, UL/ C-UL, VCCI-B,  
GOST-R, CCC  
NOTE  
* Condition: Audio equipment is not connected.  
28 APPENDIX  
 
SPECIFICATIONS: ProLite E1702SV  
LCD Panel Driving system  
Size  
a-Si TFT Active Matrix  
Diagonal: 43cm / 17"  
0.264mm H × 0.264mm V  
300cd/m2 (Typical)  
Pixel pitch  
Brightness  
Contrast ratio  
1000 : 1 (Typical)  
Viewable angle Right / Left / Up / Down: 80 degrees each  
Response time  
ProLite E1702SV-1: 5ms (Black, white, black), 2ms (Gray to Gray)  
ProLite E1702SV-2: 5ms (Black, white, black)  
Approx. 16.7 million maximum  
Analog: Horizontal 24.0-80.0kHz, Vertical 55-75Hz  
135MHz maximum  
Display Colors  
Sync Frequency  
Dot Clock  
Maximum Resolution  
Input Connector  
Plug & Play  
1280 × 1024, 1.3 MegaPixels  
D-Sub mini 15pin  
VESA DDC2BTM  
Separate sync: TTL, Positive or Negative  
Input Sync Signal  
Input Video Signal  
Input Audio Connector  
Input Audio Signal  
Speakers  
Analog: 0.7Vp-p (Standard), 75Ω, Positive  
ø 3.5mm mini jack (Stereo)  
0.7Vrms maximum  
1.0W × 2 (Stereo speakers)  
Maximum Screen Size  
Power Source  
337.9mm W × 270.3mm H / 13.3" W × 10.6" H  
100-240VAC, 50/60Hz, 1.5A  
Power Consumption  
Dimensions / Net Weight  
Tilt Angle  
40W maximum, Power management mode: 2W maximum*  
370.5 × 381.5 × 210.0mm / 14.6× 15.0 × 8.3" (W×H×D), 4.1kg / 9.0lbs  
Up: 20 degrees, Down: 5 degrees  
Operating: Temperature 5 to 35°C / 41 to 95°F  
Environmental  
Humidity  
Storage: Temperature -20 to 60°C / -4 to 140°F  
Humidity 5 to 85% (No condensation)  
10 to 80% (No condensation)  
Considerations  
Approvals  
TCO ’03, CE, TÜV-GS, TÜV-Ergonomics, FCC-B, UL/ C-UL, VCCI-B,  
GOST-R, CCC  
NOTE  
* Condition: Audio equipment is not connected.  
APPENDIX 29  
 
SPECIFICATIONS: ProLite E1702WS  
LCD Panel Driving system  
Size  
a-Si TFT Active Matrix  
Diagonal: 43cm / 17"  
0.255mm H × 0.255mm V  
250cd/m2 (Typical)  
Pixel pitch  
Brightness  
Contrast ratio  
600 : 1 (Typical)  
Viewable angle Right / Left: 80 degrees each, Up 85 degrees, Down: 65 degrees  
Response time  
Display Colors  
8ms (Black, white, black)  
Approx. 16.2 million maximum  
Sync Frequency  
Analog: Horizontal 24.0-80.0kHz, Vertical 55-75Hz  
Digital: Horizontal 31.0-80.0kHz, Vertical 55-75Hz  
137MHz maximum  
Maximum Resolution  
Input Connector  
Plug & Play  
1440 × 900, 1.3 MegaPixels  
D-Sub mini 15pin, DVI-D 24pin  
VESA DDC2BTM  
Separate sync: TTL, Positive or Negative  
Input Sync Signal  
Input Video Signal  
Analog: 0.7Vp-p (Standard), 75Ω, Positive  
Digtal: DVI (Digital Visual Interface Standard Rev.1.0) compliance  
Input Audio Connector  
Input Audio Signal  
Speakers  
ø 3.5mm mini jack (Stereo)  
0.7Vrms maximum  
1.0W × 2 (Stereo speakers)  
Maximum Screen Size  
Power Source  
367.2mm W × 229.5mm H / 14.5" W × 9.0" H  
100-240VAC, 50/60Hz, 1.5A  
Power Consumption  
Dimensions / Net Weight  
Tilt Angle  
30W maximum, Power management mode: 2W maximum*  
400.5 × 337.0 × 185.0mm / 15.8 × 13.3 × 7.3" (W×H×D), 3.2kg / 7.1lbs  
Up: 20 degrees, Down: 5 degrees  
Operating: Temperature 5 to 35°C / 41 to 95°F  
Environmental  
Humidity  
Storage: Temperature -20 to 60°C / -4 to 140°F  
Humidity 5 to 85% (No condensation)  
10 to 80% (No condensation)  
Considerations  
Approvals  
TCO ’03, CE, TÜV-GS, TÜV-Ergonomics, FCC-B, UL/ C-UL, VCCI-B,  
GOST-R, CCC  
NOTE  
* Condition: Audio equipment is not connected.  
30 APPENDIX  
 
SPECIFICATIONS: ProLite E1702WSV  
LCD Panel Driving system  
Size  
a-Si TFT Active Matrix  
Diagonal: 43cm / 17"  
0.255mm H × 0.255mm V  
250cd/m2 (Typical)  
Pixel pitch  
Brightness  
Contrast ratio  
600 : 1 (Typical)  
Viewable angle Right / Left: 80 degrees each, Up 85 degrees, Down: 65 degrees  
Response time  
Display Colors  
8ms (Black, white, black)  
Approx. 16.2 million maximum  
Analog: Horizontal 24.0-80.0kHz, Vertical 55-75Hz  
137MHz maximum  
Sync Frequency  
Dot Clock  
Maximum Resolution  
Input Connector  
Plug & Play  
1440 × 900, 1.3 MegaPixels  
D-Sub mini 15pin  
VESA DDC2BTM  
Separate sync: TTL, Positive or Negative  
Input Sync Signal  
Input Video Signal  
Input Audio Connector  
Input Audio Signal  
Speakers  
Analog: 0.7Vp-p (Standard), 75Ω, Positive  
ø 3.5mm mini jack (Stereo)  
0.7Vrms maximum  
1.0W × 2 (Stereo speakers)  
Maximum Screen Size  
Power Source  
367.2mm W × 229.5mm H / 14.5" W × 9.0" H  
100-240VAC, 50/60Hz, 1.5A  
Power Consumption  
Dimensions / Net Weight  
Tilt Angle  
30W maximum, Power management mode: 2W maximum*  
400.5 × 337.0 × 185.0mm / 15.8 × 13.3 × 7.3" (W×H×D), 3.2kg / 7.1lbs  
Up: 20 degrees, Down: 5 degrees  
Operating: Temperature 5 to 35°C / 41 to 95°F  
Environmental  
Humidity  
Storage: Temperature -20 to 60°C / -4 to 140°F  
Humidity 5 to 85% (No condensation)  
10 to 80% (No condensation)  
Considerations  
Approvals  
TCO ’03, CE, TÜV-GS, TÜV-Ergonomics, FCC-B, UL/ C-UL, VCCI-B,  
GOST-R, CCC  
NOTE  
* Condition: Audio equipment is not connected.  
APPENDIX 31  
 
SPECIFICATIONS: ProLite B1702S  
LCD Panel Driving system  
Size  
a-Si TFT Active Matrix  
Diagonal: 43cm / 17"  
0.264mm H × 0.264mm V  
300cd/m2 (Typical)  
Pixel pitch  
Brightness  
Contrast ratio  
1000 : 1 (Typical)  
Viewable angle Right / Left / Up / Down: 80 degrees each  
Response time  
ProLite B1702S-1: 5ms (Black, white, black), 2ms (Gray to Gray)  
ProLite B1702S-2: 5ms (Black, white, black)  
Approx. 16.7 million maximum  
Display Colors  
Sync Frequency  
Analog: Horizontal 24.0-80.0kHz, Vertical 55-75Hz  
Digital: Horizontal 31.0-80.0kHz, Vertical 55-75Hz  
Dot Clock  
135MHz maximum  
Maximum Resolution  
Input Connector  
Plug & Play  
1280 × 1024, 1.3 MegaPixels  
D-Sub mini 15pin, DVI-D 24pin  
VESA DDC2BTM  
Separate sync: TTL, Positive or Negative  
Input Sync Signal  
Input Video Signal  
Analog: 0.7Vp-p (Standard), 75Ω, Positive  
Digital: DVI (Digital Visual Interface Standard Rev.1.0) compliance  
Input Audio Connector  
Input Audio Signal  
Speakers  
ø 3.5mm mini jack (Stereo)  
0.7Vrms maximum  
1.0W × 2 (Stereo speakers)  
Maximum Screen Size  
Power Source  
337.9mm W × 270.3mm H / 13.3" W × 10.6" H  
100-240VAC, 50/60Hz, 1.5A  
Power Consumption  
Dimensions / Net Weight  
40W maximum, Power management mode: 2W maximum*  
370.5 × 397.0-507.0 × 236.5mm / 14.6× 15.6-20.0 × 9.3" (W×H×D),  
5.5kg / 12.1lbs  
Tilt Angle  
Up: 25 degrees, Down: 5 degrees  
Operating: Temperature 5 to 35°C / 41 to 95°F  
Environmental  
Considerations  
Humidity  
Storage: Temperature -20 to 60°C / -4 to 140°F  
Humidity 5 to 85% (No condensation)  
10 to 80% (No condensation)  
Approvals  
TCO ’03, CE, TÜV-GS, TÜV-Ergonomics, FCC-B, UL/ C-UL, VCCI-B,  
GOST-R, CCC  
NOTE  
* Condition: Audio equipment is not connected.  
32 APPENDIX  
 
DIMENSIONS : ProLite E1702S / E1702SV  
370.5mm/14.6"  
339.5mm/13.4"  
59.5mm/2.3"  
204.0mm/8.0"  
DIMENSIONS : ProLite E1702WS / E1702WSV  
400.5mm/15.8"  
368.5mm/14.5"  
55.5mm/2.2"  
174.0mm/6.9"  
DIMENSIONS : ProLite B1702S  
370.5mm/14.6"  
339.5mm/13.4"  
59.5mm/2.3"  
300.5mm/11.8"  
( ): Maximum adjustment range  
APPENDIX 33  
 
COMPLIANT TIMING  
Horizontal  
Frequency  
31.469kHz  
37.500kHz  
37.861kHz  
35.156kHz  
37.879kHz  
46.875kHz  
48.077kHz  
48.363kHz  
56.476kHz  
60.023kHz  
47.776kHz  
60.289kHz  
67.500kHz  
63.981kHz  
79.976kHz  
55.935kHz  
70.635kHz  
31.469kHz  
35.000kHz  
49.725kHz  
60.150kHz  
24.827kHz  
Vertical  
Frequency  
59.940Hz  
75.000Hz  
72.809Hz  
56.250Hz  
60.317Hz  
75.000Hz  
72.188Hz  
60.004Hz  
70.069Hz  
75.029Hz  
59.870Hz  
74.893Hz  
75.000Hz  
60.020Hz  
75.025Hz  
59.887Hz  
74.984Hz  
70.087Hz  
66.667Hz  
74.500Hz  
74.720Hz  
56.424Hz  
Dot Clock  
Video Mode  
25.175MHz  
31.500MHz  
31.500MHz  
36.000MHz  
40.000MHz  
49.500MHz  
50.000MHz  
65.000MHz  
75.000MHz  
78.750MHz  
79.500MHz  
102.250MHz  
108.000MHz  
108.000MHz  
135.000MHz  
106.500MHz  
136.750MHz  
28.322MHz  
30.240MHz  
57.283MHz  
80.000MHz  
21.053MHz  
VGA  
640 × 480  
SVGA 800 × 600  
XGA 1024 × 768  
VESA  
1
*
WXGA 1280 × 768  
1152 × 864  
1
*
SXGA  
1280 × 1024  
1
*
WXGA+ 1440 × 900  
720 × 400  
1
*
2
*
VGA TEXT  
Macintosh  
PC9801  
2
*
640 × 480  
832 × 624  
1024 × 768  
640 × 400  
2
*
2
*
2
*
*1 Available for ProLite E1702WS / E1702WSV only.  
*2 DVI input is not compliant.  
NOTE  
34 APPENDIX  
 
CONNECTOR PIN ASSIGNMENT  
D-Sub mini 15pin  
Input Signal  
Pin  
1
Input Signal  
Pin  
Connector  
Red video  
9
2
10 Ground  
11  
Green video  
Blue video  
3
Reserved port  
Data line (SDA)*  
13 H-Sync  
12  
4
Reserved port  
Ground  
5
6
Red video ground  
Green video ground  
Blue video ground  
V-Sync  
14  
15  
7
Clock line (SCL)*  
* Compliant to VESA DDC.  
8
DVI-D 24pin  
Input Signal  
Pin  
1
Input Signal  
T.M.D.S Data 2–  
Pin  
13  
14  
Connector  
2
T.M.D.S Data 2+  
1
9
8
16  
24  
3
T.M.D.S Data 2 Ground  
15 Ground  
17  
4
16  
17  
18  
19  
20  
21  
22  
23  
24  
Hot Plug Detect  
DVI-D  
5
T.M.D.S Data 0–  
T.M.D.S Data 0+  
T.M.D.S Data 0 Ground  
6
Clock line (SCL) *  
Data line (SDA) *  
7
8
T.M.D.S Data 1–  
9
10 T.M.D.S Data 1+  
T.M.D.S Clock Ground  
T.M.D.S Clock +  
T.M.D.S Data 1 Ground  
11  
12  
T.M.D.S Clock –  
* Compliant to VESA DDC.  
APPENDIX 35  
M031D01  
 

Harbor Freight Tools Staple Gun 92196 User Manual
Harbor Freight Tools Staple Gun 93926 User Manual
HP Hewlett Packard Personal Computer XE320 User Manual
Husqvarna Lawn Mower ZTH5223 User Manual
Husqvarna Tiller CT20 User Manual
Hypertec Mouse KYB LIGHTNING 01HY User Manual
iHome MP3 Docking Station iP9 User Manual
Iiyama Computer Monitor E383 User Manual
Ikelite Camera Accessories 687107 User Manual
iLive MP3 Docking Station IHMD8816DTBLK User Manual